Every CO₂ source is different: the concentration, the contaminants, the heat available and what you want to do with the CO₂. That is why we do not start from a standard plant, but from your question. Together with you, we determine what capture can deliver for your site – and then we design, test and build the solution that fits.
Your plant: CHP · incineration · biomass · smelter
flue gas with CO₂
Albatross CO₂ capture: absorber · stripper
tailored solvent · remote monitoring
Pure CO₂. for greenhouses, industry,. liquefaction or storage
Heat recovered. back to your process or. heating network
Lower emissions. CO₂-lean flue gas to stack
Three questions we answer for our clients
01 / HEAVY INDUSTRY
“I don’t yet know which capture technology suits my process”
The challenge
In sectors such as primary aluminium, the CO₂ concentration is low (around 1 vol%) and the off-gas contains aggressive components such as HF, SO₂ and COS. Reliable design data are lacking, while the investment is substantial.
Our solution
Test before you invest. We install a containerised mobile pilot plant on your own off-gas and use it to test several commercial solvents for capture efficiency, degradation and losses. Your operators run the pilot alongside us; we provide support on site and remotely.
The result
A well-founded choice of solvent and technology, the design parameters for scale-up to demonstration and industrial scale, and a reliable estimate of capital and operating costs.
Our mobile pilot plant in operation: a container with absorber and stripper columns, connected to the off-gas at the client’s site.
02 / GREENHOUSE HORTICULTURE
“I want CO2 for my crop – even when my CHP runs at a different time”
The challenge
CHP plants increasingly run when the electricity grid demands it: early in the morning and in the evening. That is precisely when the crop does not need CO₂, so it disappears up the stack.
Our solution
We capture the CO₂ from the flue gas, store it temporarily and dose it when the plants need it. Our patented solvent is amine-free, non-toxic and biodegradable: no nitrosamines are formed that could end up in the greenhouse or the food chain. The heat released goes back into your heating system.
The result
Your own pure CO₂ at the right moment, less purchased CO₂ and lower emissions. By way of illustration: a plant on four 4 MWe gas engines is designed for more than 5 tonnes of CO₂ per hour.
“I want to cut my emissions and turn the CO2 into revenue”
The challenge
Flue gases contain dust, acidic components and traces of unwanted substances, while buyers demand very pure CO₂.
Our solution
A complete capture plant with an upstream quench that removes NOₓ, SO₂, HCl, HF and dust in a single step. An FTIR analyser continuously monitors the gases at four points in the process and automatically shuts off delivery if any component exceeds its limit. Up to around 75% of the regeneration heat becomes available again at 80–85 °C.
The result
CO₂ with a purity of 99.9% as a marketable product: for greenhouse horticulture, the (chemical) industry – for example in the production of sodium bicarbonate – or for liquefaction and storage. Typical scale: tens of thousands of tonnes per year.
One partner, from first idea to operating plant
We can guide the entire process, but you can also come on board at any stage. The phases connect seamlessly thanks to our own simulation software PPS (Procede Process Simulator), developed specifically for gas treating: measurements from the pilot become design data for the next step straight away.
Design. scale-up, engineering,. costing and tender
Deliver. construction, commissioning. and remote service
Join at any stage – and decide on the next step phase by phase
Why Albatross
01
The technology follows your process.
We work with our own patented solvent as well as with commercial amines. Your situation determines which one – not our product range.
02
Heat integration as the starting point.
The energy needed to regenerate the solvent is the largest cost item. That is why we link the plant to available waste heat, such as CHP coolers, steam or process heat.
03
Proven in practice.
A full-scale plant on a wood-chip-fired boiler in Canada supplies CO₂ to a greenhouse and also serves as a test site for further improvements.
04
Specialists at the table.
Our team is led by Prof. Dr. Ir. Geert Versteeg, a specialist in CO₂ capture, supported by experts from the sectors in which we work.
YOUR NEXT STEP
What could CO2 capture mean for your site?
Contact us for an initial, no-obligation assessment. With a few details about your flue gas and heat balance, we will show you what is feasible.